Every vaper will experience a leaking vape tank at some point. You have a container with a liquid in it that you carry with you all day. It's frustrating and upsetting, but it's not the end of the world. Usually, a quick clean-up is all that is required before continuing with your day.
While the unusual e-liquid leak is completely normal, if your tank is consistently leaking e-liquid, the following tips may be useful in fixing your leaking vape tank. Leaking tanks are as unpleasant as getting a dry hit or tasting burnt. Follow our simple guide to learn how to stop and fix leaks.
When e-juice leaks from your tank, it commonly starts through the airflow system. Leaking can range from a few drops of e-liquid to your tank emptying all of its contents all over your vape mod, depending on the cause. Even the most popular sub ohm tanks have this issue.
There are some useful and simple remedies to avoid and fix vaping tanks.
Make sure you don't get any e-liquid in the central tube when you fill-up.
When you fill-up, adjust your tank at 45 degrees angle, like a glass of beer is putting.
The liquid runs down the glass or plastic inside the tank and remains as far away as possible from the middle tube.
As it fills up, resolve the tank gradually to prevent spillage.
Make sure you clear the excess by keeping some tissues at the finish and blowing the excess off of the ground if you manage to get fluids down the central pipe, or by tissue flashing in the tank.
Another issue that can lead to leakages is a basic one. Gaps form when the various components are not securely screwed together. Gaps between your coil and the base of your atomizer, as well as the base of your coil and the tank, can cause a leak.
Taking time to ensure that everything fits snugly when attaching the coil to the tank is a simple way to avoid this. Even if you haven't done anything with it recently, you should check your coil head because the connection between it and your tank can loosen when you unscrew it.
O-rings are small rubber rings that are used in a variety of uses. They're near the threading and the point where two parts of your tank meet.
They're essential for achieving a perfect seal and reducing the risk of leaks.
Over tightening, on the other hand, can harm these little helpers.
The key concept is to tightly screw everything in place while keeping in mind that you shouldn't have to use a lot of force.
There's no need to go all Hulk on it; simply screw it in snugly, but not as tight as possible.
When not in use, or even in between vapes, the unit should be stored in an upright position. When the tank is full, the holes become filled with juice, making it difficult for the e-liquid to exit.
However, when it is less than half full and not stood up, some "juice holes" appear in the e-liquid. This allows juice to flow more easily through the coil and into the central tube or out of the airflow hole.
At a higher temperature, higher VG liquid vaporizes. Because the coil is unable to properly vaporize the liquid, this can result in an excess of juice.
Low resistance coils (below 1 ohm) should be used with higher VG (thicker) liquid because the juice and airflow holes are typically much larger to accommodate the thicker liquid.
If you try to use high PG (thinner) liquids in one of these coils, flooding is likely to occur. These coils allow too much of the thinner liquid into the coil, causing it to leak out of the airflow holes or into the central tube.
Take your tank apart – this usually just entails unplugging the various parts – and look for the rubber rings on the coil head and at the bottom of your tank to check your O-rings.
Some tanks will include spares, but if not, you'll need to purchase some in the appropriate size.
It's also worth double-checking that your O-ring is properly installed, with no obvious gaps through which e-liquid can leak.
E-liquid can easily seep out of even the smallest cracks in the glass. When this happens, you'll need to get a new tank glass.
How can cracks be avoided in the first place? One option is to use a vape band, which will provide additional protection for your tank.
If you're still having issues with leaky tanks, especially if you're new to vaping, it's possible that your inhalation style is to held responsible. It’s important used to, but the solution is simple:
Make your puffs a lot longer, and don't be scared to inhale deeply. Even with soft inhalation, vapour will emerge, and your coil will not be flooded.
If you notice condensation forming in the drip tip, clean it out immediately.
Remove the drip tip, roll some tissue paper, and push it through the hole.
Nonetheless, it appears that only a few devices are completely leak-proof for everyone. I've seen devices that work perfectly for most people but leak for a small percentage of vapers. Even so, some tanks are superior to others.
Because we sell tens of thousands of tanks each year, I sought advice from the experts – our customer service team – to determine which tanks are the least problematic.
For a smooth experience, troubleshooting is sometimes required. Leaks, spit back, and hot pops can be caused by a variety of factors, but they're all preventable. Start with the most basic solutions first, and if those fail, move on to more drastic measures. If all else fails, you may need a completely new tank or device. Follow the step in the blog and we hope that your problem how to stop and fix leaks will be resolved.
It's encouraging to see that manufacturers are becoming more aware of these issues. We may be entering a new era of vaping as anti-spit back and anti-leaking measures become more common. If technology advances at its current rate, problems like these may become obsolete in the near future.
Laisser un commentaire